Synthesis and slurry spray coating of barium strontium alumino silicate on SiC substrate

Barium strontium alumino silicate (BSAS); (Ba_0.6Sr_0.4Al₂Si₂O₈) was synthesized through solid state reaction between BaCO₃, SrCO₃, Al₂O₃ and SiO₂ subjected to wet milling in isopropanol for about 24 h. The sequence of the solid state reaction was studied by subjecting to DG/DTG from room temperature to 1550 °C. The crystallographic phase evolution was confirmed by X-ray diffraction of the powders calcined in the range 1000 to 1300 °C for 2 h. The monoclinic celsian phase obtained at 1300 °C, pelletized through uniaxial pressing was sinterable to 67 to 78% density in the temperature range of 1300 to 1500 °C. The density improved to 75 to 94% after ball milling for 76 h, while ZrO₂ addition further improved the density by 2%. The celcian phase of BSAS was dispersed in isopropyl alcohol, milled for about 24 h and spray coated on to plain SiC and mullite precoated SiC substrates. Sintering of coated samples and characterization for weight gain/loss, microstructure, scratch test prove that mullite + BSAS coating is more effective than single layer coating of BSAS on SiC substrates.     

Fabrication of paper based carbon/graphene/ZnO aerogel composite decorated by polyaniline nanostructure: Investigation of electrochemical properties

The cellulose derived carbon/graphene/ZnO aerogel composite was prepared as an electrode in order to investigate the electrochemical properties. Carbon aerogel was synthesized using paper as an available cellulose source, and the composite was obtained through a new and simple preparation method including the immersion of monolithic carbon aerogel in graphene oxide/Zn²⁺ suspension and subsequent chemical reduction and freeze drying. The morphology, functional groups and crystalline structure of the samples were studied with Scanning Electron Microscopy (SEM), Fourier Transform Infrared Spectroscopy (FTIR) and X-ray Diffraction Spectroscopy (XRD), respectively. Electrochemical performance of the prepared binder free electrodes was examined using Cyclic Voltammetry (CV), Galvanostatic Charge-Discharge (GCD) and Electrochemical Impedance Spectroscopy (EIS). The data revealed that flexible carbon/graphene/ZnO composite resulted in a low density (0.035 g cm⁻³) electrode with the capacitance of 900 mF cm⁻² at a high current density of 10 mA cm⁻², lower IR drop and high cyclic stability (capacitance retention of 96%) after 1000 cycles, at 10 mA cm⁻². These features were due to the presence of 3D porous conductive network, highly reduced graphene oxide, and the formation of ZnO nanoparticles on graphene sheets. Moreover, polyaniline (PANI) was introduced to carbon/graphene/ZnO composite electrode using electro-oxidation method at different reaction time and aniline concentration in order to achieve remarkably improved capacitance of 2500 mF cm⁻² (at 10 mA cm⁻²) and low charge transfer resistance. Also, after the supercapacitor device assembly, the capacitance was retained. Based on the results, the synthesized composite is a promising material for new generation of lightweight freestanding electrodes with the high electrochemical performance.     

变压吸附制氮(PSA)设备在炼油生产中的应用

针对某炼油装置氮气供需矛盾突出的问题,提出采用变压吸附(PSA)制氮设备,利用空压站净化风生产氮气方案,(1)降低空压站多余风量放空,减少浪费;(2)正常生产情况下,利用PSA设备生产氮气,对供氮管网压力调节。针对上述方案,结合空压站供风现状进行分析,得出结论:利用PSA制氮设备满足炼油装置高峰用氮是可行的,并提出了具体措施和运行过程中应注意的问题。     

High performance H2 sensor based on rGO-wrapped SnO2–Pd porous hollow spheres

Hydrogen (H₂) sensors based on metal oxide semiconductors (MOS) are promising for many applications such as a rocket propellant, industrial gas and the safety of storage. However, poor selectivity at low analyte concentrations, and independent response on high humidity limit the practical applications. Herein, we designed rGO-wrapped SnO₂–Pd porous hollow spheres composite (SnO₂–Pd@rGO) for high performance H₂ sensor. The porous hollow structure was from the carbon sphere template. The rGO wrapping was via self-assembly of GO on SnO₂-based spheres with subsequent thermal reduction in H₂ ambient. This sensor exhibited excellently selective H₂ sensing performances at 390 °C, linear response over a broad concentration range (0.1–1000 ppm) with recovery time of only 3 s, a high response of ～8 to 0.1 ppm H₂ in a minute, and acceptable stability under high humidity conditions (e. g. 80%). The calculated detection limit of 16.5 ppb opened up the possibility of trace H₂ monitoring. Furthermore, this sensor demonstrated certain response to H₂ at the minimum concentration of 50 ppm at 130 °C. These performances mainly benefited from the special hollow porous structure with abundant heterojunctions, the catalysis of the doped-PdO_x, the relative hydrophobic surface from rGO, and the deoxygenation after H₂ reduction.     

Simply constructed highly dispersed cobalt nanoparticles in diverse N-doped graphitic carbon with remarkable performances for water electrolysis

Metal/carbon composite materials are highly promising electrocatalysts for water electrolysis. In this work, three composites of metal cobalt nanoparticles highly dispersed in N-doped carbon materials were facilely constructed by pyrolysis of different phenylenediamine based Schiff base-Co complexes (PDBs). Interestingly, the composites derived from PDBs based on different phenylenediamine exhibited different morphologies. The superior case is that rodlike composite catalyst was derived from o-phenylenediamine based PDBs. The obtained catalyst exhibited remarkable performances for both cathodic hydrogen evolution reaction (HER) and anodic oxygen evolution reaction (OER), as well as overall water electrolysis. Only 172 and 289 mV of overpotentials and 1.57 V of cell voltage were exhibited at 10 mA cm^?2 for HER, OER and water splitting in 1.0 M KOH, respectively. The catalyst also displayed robust stability and high Faraday efficiency, and thus are potential high-performance catalyst for commercial water electrolysis.     

Locating wind farm for power and hydrogen production based on Geographic information system and multi-criteria decision making method: An application

Hydrogen generation from renewable energy resources is considered as a suitable solution to solve the problems related to the energy sector and the reduction of greenhouse gases. The aim of this study is to provide an integrated framework for identifying suitable areas for the construction of wind farms to produce hydrogen. For this purpose, a combined method of Geographic Information System (GIS) and multi-criteria decision making (MCDM) has been used to locate the power plant in Yazd province. The GIS method in the present study consisted of two parts: constraints and criteria. The constraint section included areas that were unsuitable for the construction of wind farms to produce power and hydrogen. In the present study, various aspects such as physical, economic and environmental had been considered as constraints. In the criteria section, eight different criteria from technical aspects (including average wind speed, hydrogen production potential, land slope) and economic aspects (including distance to electricity grid, distance to urban areas, distance to road, distance to railway and distance to centers of High hydrogen consumption) had been investigated. The MCDM tool had been used to weigh the criteria and identify suitable areas. Analytic Hierarchy Process (AHP) technique was used for weighting the criteria. The results of AHP weighting method showed that economic criteria had the highest importance with a value of 0.681. The most significant sub-criterion was the distance to urban areas and the least significant sub-criterion was the distance to power transmission lines. The results of GIS-MCDM analysis had shown that the most proper areas were in the southern and central sectors of Yazd province. In addition, the feasibility of hydrogen production from wind energy had shown that this province had the capacity to generate hydrogen at the rate of 53.6–128.6 tons per year.     

Identification and U-control of a state-space system with time-delay

This article presents a state-space model with time-delay to map the relationship between known input-output data for discrete systems. For the given input-output data, a model identification algorithm combining parameter estimation and state estimation is proposed in line with the causality constraints. Consequently, this article proposes a least squares parameter estimation algorithm, and analyzes its convergence for the studied systems to prove that the parameter estimation errors converge to zero under the persistent excitation conditions. In control system design, the U-model based control is introduced to provide a unilateral platform to improve the design efficiency and generality. A simulation portfolio from modeling to control is provided with computational experiments to validate the derived results.     

煤基高能量密度燃料的合成及表征

高能量密度燃料是为新型高性能飞行器提供动力保障的关键,其合成及应用研究具有重要的前瞻性和重大战略意义。煤炭是我国的主体能源和重要原料,通过煤直接转化获取的煤基油,充分保留了煤中特有的环状分子化学结构,具有良好的热安定性和较高的能量密度,被认为是高超音速飞行器的优选燃料。以煤直接液化工艺生产的煤液化石脑油馏分为起始原料,通过富集轻质芳烃、化学合成、催化加氢稳定和产物分离提纯等方法制备煤基高能量密度燃料,并对其产物进行分子结构表征和性能评价。结果表明,煤直接液化生产的石脑油馏分是一种优异的催化重整原料,经催化重整富集轻质芳烃后,其轻质芳烃质量分数高达71.05%。Diels-Alder化学合成主产物是由多个封闭环平面组成且具有空间立体构型的二环或三环烃类物质,质量分数为46.18%,因分子内存在较大的张力能,结构紧凑,其拥有更大的密度和体积热值。煤基高能量密度燃料的密度和体积热值分别为0.8990 g/cm3与38.06 MJ/L,均大大超过现行的国内石油基喷气燃料(RP-3和RP-6)、煤基大比重喷气燃料、美国和俄罗斯军用标准。与单一纯物质合成高能量密度燃料(JP-10和T-10)比较,其密度与体积热值偏小。究其原因主要是轻质芳烃的富集度仅为71.05%,需进一步提高其轻质芳烃质量分数。另外,制备的煤基高能量密度燃料种类复杂,其主产物质量分数仅46.18%,下一步可重点调控合成产物的分子构型和纯化分离。     

Review and analysis of the hydrogen production technologies from a safety perspective

Hydrogen can be produced via many different technologies; however, from a safety standpoint there exists no framework for selecting the right technology. Here, we provide a structured framework for assessment of the most desirable hydrogen production technology based on efficiency, safety, and infrastructure, by using a Multi-Criteria Decision-Making (MCDM) integrated Analytic Hierarchy Process (AHP) and life-cycle index (LInX) approach. We apply this modified MCDM approach to steam methane reforming (SMR), autothermal reforming, partial oxidation, alkaline electrolysis, polymer electrode membrane electrolysis, and solid oxide electrolyzer cell processes. Our results show that SMR is the most desirable technology based on the efficiency, safety, and infrastructure criteria. We employ fuzzy set theory to address subjectivity and uncertainty challenges in the data and found that although the technologies based on electrolysis have an environmental advantage, they exhibit higher uncertainties than non-renewable technologies such as SMR. Overall, this new framework addresses the challenge to find the most desirable and safer technology for hydrogen production.